Machinery Lubrication magazine published by Noria Corporation
Issue link: https://www.e-digitaleditions.com/i/1103301
OIL ANALYSIS lubrication regime. When operating within the design conditions, compression loading is passed from one member to the next while the fluid film separates the load-bearing surfaces, thereby avoiding wear and minimizing friction and shear. At times, the interfacial shear load transfer is normal. However, in other systems, the shear load transfer can be a serious problem leading to shortened component life. is is especially true for reciprocating pistons, slides, glides, thrust bearings and journal bearings. Again, hydrodynamic and hydro- static lubrication regimes enable long life through a component separation boundary enabled by fluid film strength. Articulating and reciprocating machines are difficult to monitor using traditional vibra- tion analysis due to the perpetual direction, speed and timing changes of the duty cycles. For many of these tribosystems, oil analysis must be used alone without the benefit of vibration analysis. Bearings and gears are designed to transfer compression through the fluid film. Shear must be effectively eliminated by the fluid film to avoid failure progression. Inadequate lubrication, beginning with slip friction, is the primary interfacial shear culprit for these tribosystems. Using hardened steel on at least one side of an interface is a common practice for achieving low friction and low shear, as well as tolerance for occasional interfacial shear. e addition of extreme-pressure or anti- wear additives to load-bearing surfaces can also greatly improve component life, reduce friction and lower shear. Inadequate Lubrication Inadequate lubrication is a widespread problem with many root causes. It generally means the film strength has broken down, enabling metal-to-metal contact. Common root problems that lead to inadequate lubri- cation include insufficient lubricant, low viscosity, slow speed or excess load. Insufficient lubricant may involve no lubri- cant, low oil, cold temperatures, incompatible substances or foaming. An empty oil compart- ment has obvious consequences. Improperly filled or leaking sumps can starve a slinger ring, pickup tube or splash-lubrication system. Cold oil is difficult to pump and may not drip while viscosities are elevated. Grease mixing is a significant problem when the resulting substance does not lubricate well. Foam will not transfer heat, and air does not lubricate. e remaining hot oil also degrades, varnishes and provides poor lubrication. Low viscosity can lead to inadequate lubrication as well. It is often caused by misapplication (wrong oil), dilution or an elevated temperature. A viscosity change may indicate the use of an incorrect or potentially ineffective lubricant. Dilution of the lubricating oil by low-viscosity substances such as fuel or entrained gas may result in the viscosity dropping below what is needed to support hydrodynamic or elastohydro- dynamic lubrication. A temperature change will exponentially affect lubricant viscosity. For every 10 degrees C that a machine operates above normal, one step in the viscosity grade (VG) is needed to sustain adequate lubrication. Slow speeds may be unavoidable. Some hydrodyna mic-lubricated machines use hydrostatic jacking oil to lift the shaft while it is getting up to speed. Other machines must simply get up and go, and sometimes they must later slow down and stop. It is similar to starting or stopping a speed boat with a skier in tow. When the boat is not moving, the skier doesn't stand on the water. Slow speeds happen, and when they do, the lubrication regime changes from hydrodynamic or elas- tohydrodynamic to boundary and mixed modes. is temporary condition may work for a while, but eventually it will lead to surface damage. Extreme-pressure additives function well on hardened steel surfaces to minimize shear and avoid the onset of galling and severe sliding wear. Compression loads are supported by the lubricant film strength. is film strength is powered by the fluid and machine speed. While a high load with a high speed can be acceptable for a certain amount of time, as can a high load with a high viscosity, galling can result from a high load with a slow speed. Likewise, a high load with a low viscosity can lead to severe sliding. In tribo- systems, there are many causes of excessive loading, such as the equipment's design, operation, t wist, torque, misa lignment, component damage, etc. Inadequate lubric ation of machine components in relative motion can generate sl ip f ric t ion, r ubbi ng we a r, g a l l i ng , impacting and severe sliding wear. Slip friction and rubbing wear typically produce broadband ultrasonic stress wave energ y. Galling, impacting and severe sliding wear are forceful events which produce strong sonic stress waves that appear overwhelming in comparison to the ultrasonic activity. 18 | March - April 2019 | www . machinerylubrication.com TEMPERATURE, C VG460 VG46 VISCOSITY, CST 0 100,000 14,616 5... 449 47 30 7 10,000 1,000 100 10 1 25 50 75 100 Viscosity changes with temperature

