Machinery Lubrication magazine published by Noria Corporation
Issue link: https://www.e-digitaleditions.com/i/1103301
PERSPECTIVE compact device. Usually only a drop of oil is required, and results can be reported in minutes. Other oil parameters besides mois- ture content may be detected as well. Cost is the main downside with this approach. e calcium hydride kit is a common field test device. is test uses a reagent and a solvent (kerosene or toluene) to produce a reaction that generates gas from the existing water in the sample. It primarily measures emulsified and free water. Although low concentrations of water can be detected, this technology seems more reliable for concen- trations greater than 150-200 ppm. e crackle test is another example of a popular field test. It utilizes two drops of oil on the surface of a hot plate to evaluate the presence of emulsified and free water. e minimum concentrations that can be detected are approximately 500-1,000 ppm. With this test, it is important to pay attention to any small bubbles or crackling noise. Visual Field Inspections Field inspections for water contamination are mainly visual. Moisture can be detected through a sight glass, bottom sediment and water bowl or oil sample. Keep in mind that only emulsified and free water can be seen, so if it is visible, the concentration is quite high. Establishing inspection routines and protocols as part of your monitoring program will be critical. Online Sensors Online sensors can be installed in circulation lines or reservoirs. ey monitor water concentration directly by a saturation detector or through an indirect parameter such as the oil's dielectric constant. is strategy may offer the best alternative in terms of early detection of contamination. Online or unattended sensors may also replace some routine oil analysis. For these reasons, there is an industry trend toward using this type of monitoring strategy. e purpose of an online sensor is to emit electrical signals that are responsive to changes in the physical or chemical properties of the fluid being monitored. Most sensors contain small electrodes that are immersed in the fluid. ese electrodes generate electrical voltages and detect the oil's response in terms of capacitance, resistance, dielectric constant or current. e measure- ments are correlated with known changes in the oil's properties, such as water contami- nation, oxidation, cross-contamination with other fluids and wear debris. Some sensors have multiple measuring components, which allows monitoring of more than one property. Following are a few examples of these types of sensors currently available on the market. Moisture Saturation Sensors ese sensors detect the dewpoint and percentage of saturation of dissolved water in oil. A water-permeable polymer is sand- wiched between two flat electrodes to form a capacitor. Water penetrates the polymer to change the capacitance, which is used to measure the water-in-oil concentration. Refer to ASTM D7546 when utilizing this technology. ese are the most commonly used sensors for moisture monitoring. ere are also online water sensors that measure the total water content by percentage or in ppm. ey are capable of assessing dissolved, emulsified and free water in the oil. ese sensors provide similar information to known lab test results for water content. However, the resolution of the sensors that monitor total water content may not be as fine or precise as the ones used to monitor water saturation. Dielectric Constant Sensors is type of sensor measures an oil property that changes with oxidation, contamination or wear debris. Called dielectric constant or relative permittivity, this property is related to an oil's capability to store an electric field. ese sensors can detect changes in the oil's condition due to degradation or contamination. They must be set up for the specific fluid condi- tions in which they will work. Impedance spectroscopy and other technologies are often employed with certain styles of these sensors. Multi-function Sensors Multi-function sensors contain more than one measuring element to monitor up to three or four oil parameters, such as dielectric constant, saturation, temperature and conductivity. ey may provide more comprehensive data about the fluid they are monitoring. Some even come with connec- tivity to report results wirelessly to a remote device or cellphone. While the use of online sensors is prom- ising for the early detection of abnormal conditions and a reduction of labor, some challenges must still be overcome. It will be important for users to determine which oil properties or conditions they wish to monitor and to be somewhat familiar with 44 | March - April 2019 | www . machinerylubrication.com Multiple options are available for onsite infrared spectroscopy. Portable field test kits enable onsite oil analysis.

