Machinery Lubrication

Machinery Lubrication Nov-Dec 2019

Machinery Lubrication magazine published by Noria Corporation

Issue link: https://www.e-digitaleditions.com/i/1189076

Contents of this Issue

Navigation

Page 18 of 90

COVER STORY 14 | November - December 2019 | www . machinerylubrication.com Radio-Wave Arc/Spark Detec- tion is new stress-wave analysis technique can detect arcing, sparking and partial discharge events in electrical and electrome- chanical systems. Inspections and Special Tests Electrical discharges in oil-filled compart- ments may benefit from dissolved gas analysis (DGA) looking for evidence of turn-to-turn arcing. Deposition and accumulation of matter on f low controls, f ilters, screens, valves, fans and oil compartments are failure mechanisms resulting from a variety of operational conditions. e inspection and testing protocol will depend on these factors. For example, membrane patch colorimetry (MPC) is a preferred testing technique to identify varnish precursors. Stress-Wave Analysis Wear mechanisms of abrasion, rubbing (associated with corrosion), fatigue, adhe- sion (boundary wear), cavitation, erosion and electrical discharge can be sensed using a suitable analog sensor. Accelerometers, microphones, radio-wave sensors, current probes and magnetic flux sensors are other examples of analog sensory-input devices employed in stress-wave analysis. Analog to digital data is oversampled and selectively decimated to derive simultaneous sonic and ultrasonic peak-hold waveforms. A peak-hold stress-wave analysis waveform may be either maximum-rectified peak or maximum peak to peak. e data shown in figures 1-8 are the peak-to-peak type. e sensors utilized for these measurements were microphone or radio-wave sensors. Thermal Imaging Electrical resistance and arcing as well as mechanical friction produce hot spots that can be detected with thermal imaging. Total Ferrous A magnetometer is preferred for determining the total ferrous concentration of all ferrous oxide and ferrous metal particles from the molecular to abrasive wear particle size ranges. is tool is useful for quantifying wear and severity for ferrous debris in lubricating fluids. Vibration Analysis Mechanical vibrations below a maximum frequency of interest are monitored to characterize proactive root causes of failure mechanisms such as imbalance, misalign- ment, looseness, resonance and soft foot. ey are also monitored in combination with stress-wave analysis techniques to distinguish incipient to catastrophic stages of failure. Viscosity Lubricant misapplication, e.g., wrong oil, is frequently identified by verifying the correct viscosity for in-service lubricants. is directly relates to monitoring for inadequate lubrication associated with adhesion. Water, Coolant and Neutraliza- tion Number A convenient onsite method for moni- toring water, coolant and the acid or base number is transmission infrared spectroscopy of the in-service lubricant. Laboratory titration methods such as Karl Fischer are also effective. Water, coolant and acid are all related to corro- sive wear mechanisms. TENSION, COMPRESSION AND SHEAR "Nothing — well almost nothing — fails in compression," said John Googin, chief scientist for the Department of Energy's Y-12 National Security Complex, when asked about failure mechanisms. Googin suggested that at times when he thought compression was a primary cause of failure, a closer study of the evidence would reveal either a tensile or shear mechanism was initiating the progressive failure sequence. ree decades later, I still have not found an exception to this statement. I also have discovered that shear force is nearly always a contributing factor from incipient to catastrophic failure mechanisms. Lubricated load-bearing surfaces allow machines to work by way of compression through a lubrication film. Mechanical systems are designed to have a long life and perform work through applied tension and compres- sion. e intended long life can be cut short by shear. Failure mechanisms of abrasion, corrosion, fatigue, adhesion, cavitation, erosion and electrical discharge each have a common failure element of shear. Figures 1-8 illustrate compression and shear information using a collection of sonic Figure 1. Microphone sensor-collected stress waves from typical impacts in- volving a variety of adhesion events and fatigue defects Figure 2. Airborne stress waves from reciprocating compression with hydrodynamic fluid film separation Figure 4. Airborne stress waves from abrasive wear Figure 3. Airborne stress waves from mild adhesive rubbing wear

Articles in this issue

Links on this page

Archives of this issue

view archives of Machinery Lubrication - Machinery Lubrication Nov-Dec 2019