Sport Rocketry

Sport Rocketry 6.2020

Issue link: https://www.e-digitaleditions.com/i/1302769

Contents of this Issue

Navigation

Page 34 of 47

A Rare but Awkward Bird The F-61 Starfighter is a model not often seen at the flying field, and one can imagine this is due in part to its relative rarity (in production for just one year), and the fact that one needs those clear plastic parts to execute an accurate build. A barrier indeed to the prospective Cloner. That said, even if the special parts were readily available, one still might not make the F-61 one's leading cloning subject. One can fairly say the Starfighter is not the most graceful model, dis- playing none of the sleek lines or scale-like appearance its cousins from the Centuri Fighter Fleet possessed. Yet despite its somewhat gangly and angular appearance, the Starfighter does offer some in- teresting opportunities for enhancement. Over the course of two articles, I'd like to share with you the modifications that I chose to make to this old Classic Kit. Build Objectives While not intending to be sacrilegious, we'll diverge from Clas- sic Kit orthodoxy, and customize a few of the model's features. For starters, we'll do away with that two-tone livery and render the model in a single overall gray, as one would find on any mod- ern fighter jet (e.g.: F-22, F-35, etc.). We'll add to the two-color marking scheme by introducing a third color (black) for the textual markings (and for other detail markings), relegating the original red and blue to accent duty. We'll add some engine louvers on the aft end of the model, and a set of navigation lights to the aerody- namic surfaces. Finally, we'll perform subtle surgery on that nose cone—its clear canopy begs for a cockpit, so with some careful rocket rhinoplasty we'll attempt to give the nose a modest facelift. Build objectives set—let's get started! Airframe We begin by marking the motor mount tube for the location of the various surface appliances. I chose to work up my own mark- ing template in TurboCad. As is our practice, the balsa fins were filled with a covering of Silkspan and three coats of Nitrate dope. Each pre-finished fin was then supported with a scrap of sheet Styrene of the appropriate thickness to ensure each fin pod (1/8" diameter wood dowel) was centered on its associated fin edge while the glue set. The balance of the airframe's construction was as per the kit instructions, except for three details: • I chose not to install the engine hook, as I felt its absence would yield a cleaner look to the aft end. • I did away with the tri-fold shock cord mount, substituting instead a Kevlar anchor fastened to the forward ring that cen- ters the motor tube in the main airframe. The anchor's work- ing end was tidied up with a #7 split ring and a short length of heat shrink tubing. The actual 1/8" braided elastic shock cord will be fastened to the split ring. • I also felt the Infra-Red Photon Torpedoes would look more realistic if they were offset from the airframe. So, I cut a pair of balsa strips 1/16" thick x 3/32" wide, and glued these in place at the appropriate locations. With the glue dry and the model sanded, off to the Paint Shop for some Rustoleum Automotive Primer. Once satisfied with the primer's finish, it was time to install those aft end engine louvers. But before we can do that, we first have to make them. Engine Louvers The louvers were crafted from pieces of 0.010" thick Styrene, 5/16" long x 3/32" wide, similar in size to the louver markings found on the kit's decal sheet. A triangular support piece was fixed to each end with the aid of Tamiya Extra Thin Cement. Lather, Rinse, Repeat, and we have a set of louvers installed on the airframe. We'll do the same for the other side of the airframe as well. Some Squadron White Putty was applied to blend in the front and side edges of the louvers, and with some final primer we arrive at a smooth finish. Time to revisit the Paint Shop. Paint As we're striving for an overall "gray" finish, one might think this to be a good place to stop, except that I didn't feel Primer Gray was the Whiter Shade of Pale I was looking for. Instead, my fin- ish choice was going to be Testor's Model Master Camouflage Gray SPORT ROCKETRY NOVEMBER/DECEMBER 2020 35 MMT marking guide. Gluing a fin pod. Shock cord anchor.

Articles in this issue

Archives of this issue

view archives of Sport Rocketry - Sport Rocketry 6.2020