Issue link: https://www.e-digitaleditions.com/i/1345417
SPORT ROCKETRY MARCH/APRIL 2021 19 this difference in the "noise"? I'll let you decide. Figure 5 is a pic- ture of the "200 Meters or Bust" rocket after recovery and with the flight card. Notice the peeled body tube is pretty toasted at the en- gine ejection point. It literally fell apart when I tried to remove the motor, but it had served its function. Now getting back to the shock cord break⦠I had started out using 135 pound Kevlar, but found the approximately 30" foot piece I was using weighed 1.5 grams! So I switched to 65 pound Kevlar, which weighed around 0.4 grams and it wasn't up to the task. Some ideas to deal with it breaking: 1) Make sure the stream- er stays with the nose cone and altimeter like it did on my flight, or 2) Don't attached the shock cord to the rocket at all, just to the nose cone/altimeter section and let the booster free fall. It will be unstable or stable in the wrong direction and it will descend tum- bling or like a Space-X booster. Either way, the mass of 5 grams (includes the spent motor casing) will be no cause for safety con- cern (featherweight recovery). With that concept, the engine block can be removed to save more weight. This will work if the engine is tightly friction fit and that there is wrap or two of Mylar tape on the protruding end of the motor to fit it tightly into the piston tube. That tape will serve as an engine block. Eliminating the internal en- gine block will save a few tenths of a gram in weight too. This is the plan I will use for my next flight. The downside is you risk losing the booster so use markers to color it a bright color. "200 Meters or Bust" Plan and Building Notes An adjacent page shows the plan for my "200 Meters or Bust" design. Here are some build and flying tips. 1. For Kraft paper tubes I sand a slightly longer than needed length tube, starting with 240 grit sandpaper, then 400 grit, then 600 grit, 1000 grit and 1500 grit sandpaper. The tube comes out pretty smooth doing this. Perhaps not pol- ished, but not too bad for a few minutes work. 2. After sanding I cut some off of each end to make the tube the proper length with the tube ends nice and clean. 3. Next I peel out the inside layer of paper. I find that some tubes peel more easily than others. In particular, I find the Balsa Machining Service T5 tubes very difficult to peel suc- cessfully. Since this tube is only 5.5" long, it is a little easier but my success rate is still low. My best luck these days has been the old Totally Tubular tubes that eRockets later sold (they may be back in stock, but I don't know if they are the same ones). The ones I have may be the original TT tubes that sat through several temperature cycles in Jim Fack- art's barn. This may have weakened the glue in the paper layers, making it easier to remove the inner ones. Fortu- nately I still have some of those old tubes around. Estes BT-5s used to peel well and even could be "Super Peeled" per Bernard's article, but I haven't tried it with them for a while. Another option may be to sand the inside of the tube to remove extra paper. 4. For fin attachment, I use my simple fin jig. See the Jan/Feb 2020 issue of Sport Rocketry for details on it. CA adhesive for attachment and tiny epoxy fillets. 5. Use whatever shock cord strength you are comfortable with. I will continue to use the 65-pound strength due to weight and allow the booster to tumble in. 6. The altimeter fits fairly snug in the nose cone section, but a wrap of tape over the back end is prudent to keep it in place. I forgot to do that on my 221m flight and the altim- eter was half way out when I recovered the model! 7. Fold the battery and altimeter unit so that the sensor is on the inside and all the way up in the nose to shield it from sunlight as much as possible. Even with that, the sensor may still get some exposure to sunlight. That will cause spikes in the data on descent as the sensor gets exposed to the sun. The filter button in the Adrel software will remove those. See figure 6. 8. Finally, this design is optimized for 1/2A3-4T motors and with an ALT-BMP altimeter in the nose. It will be unstable with an A3 motor or without the altimeter installed. I hope you decide to build the 200 Meters or Bust. If you do, let me know. Good luck and have fun joining the 1/2A Altitude 200 meter club!

