Issue link: https://www.e-digitaleditions.com/i/1542573
D21 ~Series I under hood muffler made to spec from the original Allis blueprint from the early-'60s! Only reproduction muffler on the market! $550 ~Fender skirts, $350 a pair ~Battery box left or right (does not include side cover), $275 ~Battery box side cover with 4" step, $95 ~Battery box side cover without step, $85 ~Frame rail step, $95 ~Factory foot throttle kit, $175 ~Under hood long side panels, $200 a pair or $100 each ~Platform dipstick round cover, $30 ~Grill latches, $15 each ~Shifter cut out cover, $40 ~PTO shield, $95 ~Floor plates left or right, $150 each ~Lift arm release latch, $50 ~Instrument panel, powder coated gloss black, $100 ~Bell housing pivot bushing for wide front end, $60 ~Front cast pivot bushing for wide front end, $80 ~Aftermarket grab handle, powder coated silver sparkle, $40 ~Front radiator panels, $175 each ~Stainless steel grab handle, $50 ~Front axle wishbone 4-piece repair kit, $350 ~NEW Sway blocks, sold in pairs only, $300 ~NEW 3-point adjuster crank lever, $60 220 and 210 ~Fender skirts with triangular filler plates, $350 a pair ~Triangular filler plates, $60 a pair ~220 battery box left or right (side cover not included), $275 ~220 only; battery box side cover with 8" step, $105 ~220 only; battery box side cover without step, $85 ~210 battery box (left or right), $275 ~Frame rail step, $95 ~Right side frame rail step kit, $125 ~Side console PTO cover, $80 ~Under seat frame hydraulic line cover, $70 ~Left rear corner platform panel, $60 ~Brake cover wire ring, $60 ~Brake cover spacer washer, $2.50 ~Bell housing pivot bushing for wide front end, $60 ~Front cast pivot bushing for wide front end, $80 ~3-point trunnion arm bushing, $50 ~Left hand filler panel used on tractors w/o fender skirts, $75 ~Aftermarket grab handle, powder coated silver sparkle, $40 ~Under hood behind engine air deflector baffles, $80 ~220 only front under hood side covers, $150 a pair or $75 each ~Rear under hood side panels, $100 a pair or $50 each ~Fuel tank to fender one hole clamp, $16 ~Fuel tank to fender two hole clamp, $21 ~Fuel tank to console one hole clamp, $16 ~Fuel tank to platform clamp, $8 ~Platform dipstick round cover, $30 ~220/210 fender angle brace set; this will make a 2 brace upright 200 fender into a 220/210 fender, $150 a pair or $75 each ~170-210 grill latches, $15 each ~210 lower grill insert, $160 ~220/210 suitcase weight bracket, $275 ~220/210 floor plates left and right, $150 each ~220/210 PTO shield, early smaller style, $95 ~220/210 PTO shield, later bigger style, $105 ~220/210 instrument panel, powder coated gloss black, $80 ~Lift arm release latch, $50 ~100 Series thick suitcase weight lock bar, $20 ~Removable tool box bracket for factory black tool box, $40 ~Stainless steel grab handle, $50 ~Front axle wishbone 4-piece repair kit, $350 ~NEW Sway blocks, sold in pairs only, $300 ~NEW 3-point adjuster crank lever, $60 200 ~Rear underhood side panels, $75 ~Suitcase weight bracket for the 12 thin weights, $250 ~NEW 3-point adjuster crank lever, $60 ~100 Series thick suitcase weight lock bar, $20 190 ~Early style long side panels, $100 each ~Rear under hood side panels late model, $75 ~Suitcase weight bracket for the 12 thin weights, $250 ~NEW 3-point adjuster crank lever, $60 ~100 Series thick suitcase weight lock bar, $20 180/185 ~Rear under hood side panels, $75 each ~Suitcase weight bracket, $250 ~NEW 3-point adjuster crank lever, $60 ~100 Series thick suitcase weight lock bar, $20 170/175 ~Rear under hood side panels both early and late style, $75 each ~Suitcase weight bracket, $250 ~NEW 3-point adjuster crank lever, $60 ~100 Series thick suitcase weight lock bar, $20 18.4-16.1 ~Wheel reinforcement ring, $75 each 7010, 7020, 7030, 7040, 7045, 7050, 7060 ~Open station parts list. Everything needed to make your tractor an open station minus the fenders. All large frame 70 Series tractors. ~Fender to axle brackets, $90 each ~U-bolts for fender to axle brackets, $150 a pair ~Seat mount panel, $80 ~Seat mount platform base, $150 ~Under seat platform bracket, $30 ~Hydraulic bank/under seat mount panel, $100 ~Middle floor plate, $150 ~LH floor plate, $175 ~RH floor plate, $165 ~RR floor plate, $60 ~LF fender support bracket, $50 ~Left front floor mat clamp, $15 ~LH floor mat clamp, $25 ~RH floor mat clamp, $23 ~SMV bracket, $40 ~Open station floor mat, $200 ~Complete open station kit minus the fenders (includes everything listed above in the proper quantities), $1,550 D & L TRACTOR PARTS DALE & LUKE ROOZEBOOM 3038 240th St., Rose Hill, IA 52586 All parts are powder-primed for quality and long-term storage! Best fit on the market, guaranteed! Built to OEM specs! Made in the USA! One nation under God! For order info, call Luke, (641) 660-4150 Specializing in D21, 220 and 210 Allis-Chalmers tractors All parts are laser cut machine bent copies, blueprinted from originals. Cast parts are patterned from NOS parts. Best fit on the market! You will not be disappointed! If you are not satisfied with your parts, I will return your money less shipping. Prices subject to change without notice. 6-1-2024 50 OLD ALLIS NEWS