Issue link: http://www.e-digitaleditions.com/i/666229
2014 RANCHO ® Footnotes 225 FOOTNOTES MUST BE READ! THEY CONTAIN IMPORTANT INFORMATION AND RECOMMENDATIONS PERTAINING TO CERTAIN APPLICATIONS. 92. Factory rear springs must have a flat measurement eye to eye of 52 9 . Some heavy duty rear springs measure 56 9 flat and cannot be replaced. 100. Except dual rear wheels. 112. Dana has no outer lip on the rear cover. Chrysler does have an outer on the rear cover. 120. Camber adjustment may not be possible on some raised vehicles. RS6406 coil springs will only work on raised vehicles. 123. Most 92-96 fullsize 4WD Bronco and F-150 trucks are equipped with the lower mount of the factory quad shock option, which is needed to mount our RS97489, RS98508, RS5565 & RS5566 steering stabilizer systems. 124. If vehicle has 2 1 ⁄2 9 wide leaf springs, use Bracket Kit RS50616. 131. Raised height may vary depending upon vehicle GVW. 132. These leaf springs do not come with bushings. Bushings are in front Kit RS6444. 133. Transfer case Lowering Kit No. RS6641 may be required on some vehicles. 146. Optional Upper Link Kit for added performance and handling. 148. Do not use with after market (stamped steel housing) ball joints. Use only with OE style (forged housing construction) upper ball joints. 149. This unit installs in an auxilliary position and may be used in conjunction with the O.E.M. position stabilizer. 152. This is a spring-seat shock absorber. 154. Exhaust modification is required, check local laws regarding exhaust modification prior to installation. 155. Part number RS40054S may be substituted for RS86206 applications. This spring will give a firmer ride and will have limited suspension travel. 156. These springs are not designed for hauling. 177. Remove and replace #2 leaf. 182. Has grease fittings. 185. Except 4000 lb front axle. 192. Front Driveshaft vibration may occur in 4 W.D. only. A replacement driveshaft (part no. 3194-1000) is available from: Powertrain Industries, Inc. 7532 Anthony Ave. Garden Grove, CA 92841. Toll Free: 1-800-798-4585. Email: sales@powertrainindustries.com. 197. Ford F150's which have a ("L" - shape bolt pattern for the transmission cross member must use the RS6489 Primary Suspension System; trangular bolt pattern use RS6488 Primary Suspension System. 199. This system cannot be used with any wheel with backspacing that exceeds 4.5 9 and/or the wheel diameter is less than 16 9 . 200. Steering arm may contact shock body on RS999113 & RS999119 on FJ43 & FJ45. Install shock boot towards ground for additional clearance. 203. RS6740 or RS6741 Bracket Kit includes four RS5298 shocks. 205. Ford Superduties are equipped from the factory with either a "tall" (3.7 9 ) rear block or a "short" (1.9 9 ) rear block. Rancho ® offers three different choices to accomodate this option. 1. RS44154: Soft ride rear leaf spring is designed to add up to 1" of rear height. 2. R80053: Rear block kit adds 2 1 ⁄2 9 to rear height on vehicles equipped with the O.E. "short" block and 19 to vehicles equipped with O.E. "tall" block. 3. RS60642: Rear add-a-leaf kit is designed to add up to 2" of rear height. 207. Springs are not included with this system and must be ordered separately. 209. New upper ball joints are not included with this suspension kit but are required to complete the installation, reference instruction sheet for complete listing. 210. Some vehicles may experience a rear driveshaft vibration. A replacement rear double-cardan driveshaft for Rubicons only (part number 3394-0100) is available from: Powertrain Industries, Inc. 7532 Anthony Ave. Garden Grove, CA 92841. Toll Free: 1-800-798- 4585. Email: sales@powertrainindustries.com. 211. RS40054S may be used as a HD replacement. 220. Carrier bearing spacer P/N RS6608 is required on vehicles equipped with rear drive shaft carrier bearing. Vehicle may exhibit minimal driveline vibration in 4WD. 221. Optional front skid plate (RS8716B) and differential skid plate (RS6201) can be purchased separately. 251. Front swaybar endlink kit REQUIRED. 252. Requires Rancho ® 's cat-back exhaust system - (4 door models require P/N RS720001•) (2 door models require P/N RS720002•). 253. Long Arm Suspension. 254. Rear kit, required to level the rear to the front height. 255. Optional quick-disconnect front endlink kit can be purchased separately. 256. Interference with the catalytic converter may prevent installation on 2008 Super Duty vehicles with the 6.8L V10 engine. 259. Front driveshaft required, (2DR: Front: PN 3194-1925: PN 3194- 0725) (4DR: Front: PN 3194-1925 Rear: 3194-2750). Powertrain Industries 7532 Anthony Ave. Garden Grove, CA 92841 714-901- 3611. 312. This unit converts the vehicle to a non electronic suspension. 313. Not for use with aftermarket shock spacers or relocation brackets. 314. Optional ( 3 ⁄4 9 ) coil spring space is available for vehicles equipped with aftermarket bumper and winch. 315. Optional high clearance Rancho ® cat-back exhaust system (4 Door P/N RS720001) (2 Door P/N 720002). 316. Requires Rancho shock adapter bracket. 319. Must use w/ RS66501B when using O.E. front strut. 320. Requires at least 2-in. tall front bump stop spacers. 321. Requires a 2-in. minimum lift to use; Stabilizer protective boots can not be used. A3. New Part Number Available Third Quarter. A4. New Part Number Available Fourth Quarter. PS. Rancho ® RS9000X Pro-Series shock absorber. Q2. Qty. Req. 2. Q4. Qty. Req. 4. QL. Loaded is pre-assembled with coil spring and upper mount. XL. Designates XL shock absorber. • New Part Number, Check availability before placing order.