Sport Rocketry

Sport Rocketry 2.2020

Issue link: https://www.e-digitaleditions.com/i/1220484

Contents of this Issue

Navigation

Page 33 of 55

the object itself. Now, remove the sand paper from the body tube and with the shape now sanded in relief into the back- ing block, you glue on the hook-and-loop to the block (Figure13), press on a sanding sheet, and begin sanding the tube down with a perfectly shaped sanding block (Figure 14). Instead of sanding at a single point, you are now sanding a cylinder with 100% contact. I can confidently assure you that this method is as superior to block sanding as my brain is to that of an infant (What honey? My brain and an infant are what? Yes, dear, I love you too.) Figure 15 shows some of the other off- the-shelf shapes that Festool has available. I can readily imagine the 10mm radius pad working beautifully on HPR fin fillets. Even the 90° corner sander would work on smaller fillets. Use the flat pad obviously on fins of any material, and the 6mm in- side radius pad on fin edges. Talk about perfectly rounded edges. I love my bench band-sander, but I can never get perfect fin edges—due to the imperfect amounts of pressure manually applied from fin-tip to fin-tip, the sanded surface inevitably ends up with slightly different lengths and depths along the edge. With every fin dif- ferent in a slightly different way, and while these differences are small, the resulting imperfections are both visible and aerody- namically flawed. And, a flawed rocket at NARAM is a very bad thing. While a flawed rocket displayed with joyful pride on my living- room coffee table will contentedly sit there until my wife gets home, a flawed rocket at NARAM will get you…Well, just imagine with me: You're walking from the dusty parking lot to the check-in table holding, no—cradling your beloved in your arms. Suddenly a hush sweeps over the expect- ant rocketeers, the RSO shifts his glasses while peering over the top of the rim. His brow furrows. The crowd, pretending not to stare, stare anyway. You begin to sweat. The RSO begins to clear his throat. Con- fused, you look down at your gleaming rocket destined to carry you to fame, and you see the flaw upon which every gaze is focused; a bump, a lump, an imperfectly sanded bit of spiral-filling JB Weld! Fleet- ingly, you wonder if you could carve the visages of Mt. Rushmore into its bulbous surface before you reach the RSO table; 34 MARCH/APRIL 2020 SPORT ROCKETRY ESTES, QUEST, CUSTOM • Rockets • Engines • Bulk Packs • Accessories • Parts PERFERRED CUSTOMER SPECIAL DISCOUNTS NAR & Tripli Members Only Telephone or Fax Orders (include your member number) Send for your free catalog or visit us at: Belleville Wholesale Hobby Inc. 1944 Llewellyn Road Belleville, IL 62223-7904 www.bellevillehobby.com www.estesrocketswholesale.com www.questrocketswholesale.com Call 1-618-398-3972 HHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHH H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H claim it was a scale-rushmore-model rock- et instead of a Mach-buster. Before you can even break out your carving pen-knife, the RSO says in his best outdoor voice, "That rocket is flawed! Only perfectly perpen- dicular, linearly sanded, spectacularly cir- cular, air-hole punches are granted launch status on this hallowed ground." And ev- eryone turns their backs to you leaving you wishing that you'd listened to your wife and taken up knitting instead. Yes, my friends, that vision was my dai- ly motivation to a perfectly sanded model rocket. And Figure 16 shows the gleaming sides of the Rudy III rocket. Which I sup- pose is at least one moral to our sanding saga: Always carry your rocket with Mt. Rushmore on the bottom. In the end I've discovered that the only way to produce a rocket body that meets reasonable stan- dards of attraction is to marry the right girl, or use a linear sander. The sander is way less maintenance, and with it I was able to sand the JB Weld right down flush before my biological children put me in a nurs- ing home. My aerodynamically gleaming babies were a complete success topping 1,140 feet on an H148 and 4,575 feet on a J270 (Figure 17). So I got Level 1 and 2 done (Figure 18) while my eyesight was still sufficient to see the tracking smoke! By the way, does anyone know of a nursing home where the residents are al- lowed to have their tools, rockets, and ex- perimental motor fuels in their room next to their IV machine? Please PM me if you do, I like to plan ahead. About the Author: Kevin Cornwell and his wife Madeleine actively promote rocketry in STEM programs in the Hilo community. Their home has a lovely view of Hilo Bay, which provides a con- stant distraction from sanding.

Articles in this issue

Links on this page

Archives of this issue

view archives of Sport Rocketry - Sport Rocketry 2.2020