Sport Rocketry

Sport Rocketry 5.2021

Issue link: https://www.e-digitaleditions.com/i/1408247

Contents of this Issue

Navigation

Page 28 of 47

SPORT ROCKETRY SEPTEMBER/OCTOBER 2021 29 cally. The launch is triggered via a wireless controller but all functions are automati- cally performed by the camera controller. The controller even shuts itself off after the liftoff to conserve battery life. Liftoff of a rocket is detected by a switch mounted on the rail just above the lower rail button to accurately sense when liftoff occurs. The pitching camera mounts use this signal to start movement of the cameras. The rate at which the camera pitches is matched for the rocket's acceleration and is set into the con- troller during pre-launch activities. There can be over two dozen cam- eras that have to be prepared each with unique settings, all have to have the batter- ies charged, media cards formatted, tested, and mounted in addition to preparing the rocket for launch. It may take weeks to get everything ready and set up for the launch. Some of you know how difficult it can be to ignite a cluster of high power rocket motors. The 54mm motors for the strap-on boosters have cores that are substantially smaller than the 98mm main motor. Several techniques were used to ensure that all the motors ignited simultaneously. First, the fir- ing of the igniters is staggered. The igniter for the main motor is fired over a half sec- ond prior to the firing of the strap-on boost- er igniters. This is easily accomplished with the controller since there are two separate ignition circuits. In addition, a current lim- iting circuit was used to prevent the current in any e-match from exceeding 1 amp. This is so that one igniter cannot create a short that it would inhibit the other igniters from firing. Finally, there are two e-matches for each motor. All of this ensures the motors come to pressure simultaneously. I was very fortunate to be assisted at the launch by James Allison and Reyes Banda. Both had virtually no rocket experience yet volunteered to assist me with filming, launching, and recovering of Final Cut. We arrived several days early to set every- thing up and start filming. Unlike previous launches, I wanted to do a lot of filming in advance of the actual launch day. We load- ed the rocket on the launch tower, recorded an 'interview' of myself, even recorded B roll footage for a video I wanted to make about this project. However, the weather didn't cooperate and every afternoon, high winds came up and interrupted the record- ing schedule. When actual launch day arrived, all I concentrated on was the rocket. The launch would be recorded but I virtually ignored filming of anything else. The pressure was enough remembering all that needed to be done. Making a checklist weeks before the launch turned out to be a tremendous asset. There were 27 individual items, (cameras, altimeters, timers, camera control circuits, wireless transmitters, etc.) that needed to be turned on immediately prior to liftoff. The liftoff was going to be less than 5 Gs off the pad. Failure of any motor to ignite, or even of there was a substantial delay in ignition, the results could be catastrophic. Adding an extra length of rail to my pad was good, but would it be enough? I could feel the stress building inside. Probably my biggest worry was whether all the motors would light and how close to the same time. Because of the number of items on the checklist to turn on, I coor- dinated with the LCO in advance to limit the introduction and proceed quickly with a countdown. When the motors came to life, it was both remarkable and a relief. The sight was beautiful and Final Cut flew straight and true. The strap-on boosters deployed as de- signed and remarkably the rocket landed fairly close to the flightline. The results were more than I had hoped for. I believe the video footage and the still images are the best that I've ever done and many seem to agree. Because the liftoff was so slow, the dirt from the blast of the motors was blown 20 feet high and 50 feet from the launch pad. This created spectacular images but the on-board cameras were just as remarkable. The rocket rolled about ¾ of a turn and then seemed to stop with the flightline in view to nearly apogee. The foot- age and images from the strap-on boosters separating and even separation at apogee were better than I expected. The slow mo- tion footage from on board stunningly cap- tures the beauty, grace, and the destructive nature of rocket flight. That is not to say the flight was perfect; far from it. The strap-on boosters were de- signed to be stable after separating from the main rocket but the footage clearly shows them tumbling. As a result, a few of them are damaged and one was completely lost. The main parachute was tangled so the main rocket descended faster than desired but it suffered only cosmetic damage. A few cameras did not record or stopped pre- maturely and the tumbling of the strap-on boosters made that footage difficult to use. However, I was so please with the re - sults that I did get that the redesign of the strap-on booster has already begun. I don't know when Final Cut will launch next but I can't wait. Video of the launch can be found at https://vimeo.com/558878230 Quickly Locate Your Downed Rocket in MINUTES! Powerful Tracking Transmitters 2-9 Mile Ground Tracking Range/10+ Mile Air Tracking Range Lightweight Transmitters 2 Grams & up Waterproof Circuits Durable and Easily Transferred from Rocket to Rocket Telemetry Specialists Since 1970 Receiver Models Tracking from 3 to 200 Rockets Formerly Walston Retrieval TRACK YOUR ROCKET FROM LIFT OFF TO LANDING! 1202 Walnut Street Murphysboro, IL 62966 800-842-4537 Toll Free www.wmimodelaeronautics.com 618-687-3505 Fax: 618-687-3539 Email: mikec@caretrak.com

Articles in this issue

Links on this page

Archives of this issue

view archives of Sport Rocketry - Sport Rocketry 5.2021