Sport Rocketry

Sport Rocketry 2.2021

Issue link: https://www.e-digitaleditions.com/i/1345417

Contents of this Issue

Navigation

Page 21 of 47

22 MARCH/APRIL 2021 SPORT ROCKETRY cover techniques that are unique to this build. And while most of the materials for this build are pretty standard and readily available, the only special parts needed are BT-50/60 or BT-55/70 centering rings, and the optional aluminum mesh for a para- chute shelf. I like to build the motor mounts first since I almost always have those general parts on hand. The 18mm motor mount is simple and standard so it doesn't warrant further explanation. The 24mm mount is also standard, but with two modifications. Since the body tube on the 70 is fairly long, I made the motor tube about 9 inch- es long. This helps with strengthening the main tube and maintaining adequate ejec- tion pressure. Also, a 4 or 5 inch sleeve of BT-52 tube was glued over the engine tube Building and Building and Flying the Flying the OmegA OmegA by Mike Moran Figure 1. Artist's rendition of the Northrop Grumman OmegA. Did you see the new launch vehicle that Northrop Grumman had planned to build, the OmegA? I thought it was a cool looking rocket that would make a good fly- ing model. Sadly, the OmegA project was cancelled in September of 2020, but not before I made a scratch-built model.Well, two actually. One is about 28 inches tall with a BT-50 main tube and a BT-60 pay- load section. The other, about 40 inches tall with a BT-55 main tube and a BT-70 payload section. These are renditions rather than scale models. I did something similar with the Delta II, and it turned out pretty cool. See Figure 2, the cover photo of this issue. Since I name similar rockets by their Figure 6. Aluminum mesh parachute shelf and harness for the 70 version. about 1 inch down from the forward end of the engine hook. This helps protect the motor tube from the expanding and col- lapsing pressures some longer tubes may be subjected to (see Peak of Flight Newslet- ter issue #418). I do it all the time, never had one fail. After I gathered all my body tubes and couplers, I cut the tubes to their specific lengths. For the 60, the BT-50 main tube is 13.25", the upper 4.75", and the BT-60 payload 5.5". The dummy SRBs are 10" BT-5 tubes. The fins have a 1" root and semi-span, with a 3/8" tip. The dimensions for the 70 are shown in the illustration. For the transitions, visit our friends at Payload- bay.com and use their transition tool. Make the transition length 0.75" for the 60, and 1.0" for the 70. Also, print a BT-5 two-fin wrap to draw two lines down the length of the SRBs. If you are new to rockets with tran- sitions, here are a couple of tips. When you're ready to attach the payload section, payload section size, the smaller rocket is the OmegA 60 and the larger the OmegA 70. The 60 uses 18mm motors, while the 70 is built for 24mm applications. Simu- lations put the projected altitude for the 60 at a little under 400 feet, while the 70 comes in at an impressive 1060 feet. In- cluding my standard electronics cargo of 20 grams, the sims show stability calibers of 3.61 and 3.45 for the 60 and 70, respec- tively. I built the rockets concurrently, but I planned on finishing the 60 a little ahead of the 70 so I could fly it first to evaluate its performance. The very fact that you are reading this magazine suggests that you are somewhat of an experienced modeler. So I'll only

Articles in this issue

Links on this page

Archives of this issue

view archives of Sport Rocketry - Sport Rocketry 2.2021