Machinery Lubrication magazine published by Noria Corporation
Issue link: https://www.e-digitaleditions.com/i/1433576
www.machinerylubrication.com | November - December 2021 | 37 them $3,000. It was not until they switched their sampling method to the Checkfluid LP & KP Pushbutton valves that the real problem was discovered. e technician taking the samples was using the same plastic tubing when he sampled the coolant and then the engine, leading to cross-contaminated samples. Reduce Consumption By upgrading your lubrication program, you will most likely see a reduction in the machine's energy and oil consumption. ese reductions will oftentimes give companies the biggest return on investment and the biggest demonstration of carbon reductions. e carbon credit system being proposed is intended to discourage, where possible, carbon products like oil from adding to the CO2 in the atmosphere. As we saw in a recent United Nations short report on climate change, science is telling us that CO2 acts as a blanket like a greenhouse. e more CO2 that blankets the atmosphere, the more the sun's rays will heat the planet and cause climate and ecosystem disruption. e carbon credit is a way of keeping score. Whether it is part of a company, national system or international system, the carbon credit is used to fund initiatives that reduce CO2 emis- sions. ese initiatives can be entirely local or, in the case of multinational companies, can be international. For example, Shell in Canada offers consumers, when they fill up with gas, the opportunity of contributing two cents per liter to offset their carbon footprint. Unfortunately, politics can get in the way of taking action. Our objective should be to make our depart- ment or company carbon-neutral. First, let's look at oil consumption. Did you know that each gallon of lubricant consumed contributes to 23.6 pounds of CO2 emis- sions [3]? is means that a 55-gallon drum contributes to approximately 1,300 pounds of CO2 emissions. A carbon credit is equal to 1 ton of CO2, or approximately 85 gallons (320 liters) of oil. Using the current system, carbon neutrality would cost a company a $35 surcharge for consuming 85 gallons of oil. But by actually reducing oil consumption by 85 gallons, a company can save approximately $640 based on a $2 a liter/quart price of oil. It pays to optimize your drain interval. Here is an example: A company-wide KPI for a plastics manufacturer was to reduce carbon emissions by reducing lubricant waste. For them to optimize drain intervals on their machines, they installed condition monitoring hardware and looked at in-service filtration. From 2017 to 2018, the company increased the amount of oil they were able to filter and retain in their machines by 27.4%. ey were able to reduce their CO2 emissions from wasted oil from 22,533 pounds of CO2 in 2012 to 3,779 pounds of CO2 in 2018, an 83% decrease in emissions by optimizing their drain intervals. is company was also able to save thousands of dollars in oil disposal costs. Let's talk about fuel consumption. Reducing fuel consumption in mobile equip- ment can be the most significant contribution to reducing CO2 emissions. Many of these strategies are outside of the scope of this article, but they include: • Burning low sulfur fuels • Reducing unnecessary trips • Keeping tires inflated to correct levels (especially important for on or off-highway trucking) Oil viscosity can also play a role; moving a thicker fluid takes more energ y. If you reduce viscosity, less energy is consumed in the moving parts and in pumping the fluid around the engine. But at a lower viscosity, base oils are more volatile and likely to evaporate; you need the additives to work a little harder. To reduce fuel consumption and emissions, oil analysis and proper oil samples are vital to make sure the engine oil is clean, the viscosity is correct and the additive levels are good. Next up is a reduction in electrica l consumption as energ y savings can be looked at in terms of what is used to operate the machine. An efficient running machine will use less energy than its counterparts. For an electric motor and/or gearbox, this would be a reduction in electric energ y (voltage, current and power factor). Tracking electrical consumption is a reliable way to document energy efficiency improvements regarding changes in a lubrication program. Studies have seen that, typically, companies that upgrade their lubrication and reliability practices have been able to document a 5-15% reduction in power requirements [4]. Another interesting way of measuring improvement on a day-to-day ba sis is tracking the machine's operating tempera- ture. Proper lubrication and monitoring can reduce the friction between two surfaces, and thus, the amount of energy needed to move those parts against each other. When that friction is reduced, less electricity is required to operate the machine. Although it's unlikely to reveal the amount of energy Figure 3: Examples of Dedicated Sampling Valves ML ML

