Issue link: https://www.e-digitaleditions.com/i/1138630
38 July 2019 Tablets & Capsules increased. From the Heckel plot, the yield pressure of plastic deformation (YPpl) and yield pressure of elastic deformation (YPel) were derived. Table 1 shows the work of compaction (WoC), work of elasticity (WoE), yield pressure of plastic deformation (YPpl), yield pressure of elastic deformation (YPel), ejec- tion force, porosity, and tensile strength (TS) values for the four excipients at 50, 100, and 150 megapascals of compression force. Material-predominant deformation was identified using principal component analysis (PCA). It was observed that brittle materials are associated with high YPpl and YPel values, plastic materials are associ- ated with high WoC values, and elastic materials are associated with high WoE values. Figure 2 depicts a PCA score plot that groups the dif- ferent materials by deformation mechanism. The results show Starch 1500 with dominant elastic deformation, Emcompress and Parteck M200 with dominant brittle fracture deformation, and Emcocel 90M with dominant plastic deformation. Using these evaluation techniques can help devel- opers with: • selecting formulation ingredients; • designing tablets, including concavity and profile shape; • choosing punch-head options to provide longer or shorter consolidation or dwell times; • determining whether precompression and tapered dies are needed to exhaust entrapped air from the material in the die; and • reducing tablet press wear and tear from excessive compression forces and friction. Plastic deformation. With plastic deformation, the strain caused from applied stress will continue to increase until the load is removed. Therefore, the amount of strain is time-dependent. A material that exhibits this behavior is microcrystalline cellulose. In practice, most materials possess a combination of these characteristics, resulting in some degree of visco- elastic behavior. In time-dependent deformation pro- cesses, if the particles aren't given enough time to deform, the material will react in some other way. This is a common source of problems for products being scaled up from an R&D tablet press to a high-speed production tablet press, where less time is given to make each individual tablet. Furthermore, the material will undergo some degree of time-dependent recovery after the compression load is released, and if the tablet was not sufficiently formed at the point of maximum compression force, this recovery may result in tablet structure failure. Planning for scale-up Identifying material deformation characteristics at the development level allows developers to formulate a drug product to withstand the compression dynamics of a high-speed production tablet press. Figure 1 depicts Heckel plots for the commonly used excipients micro- crystalline cellulose (Emcocel 90M, JRS Pharma), prege- latinized starch (Starch 1500, Colorcon), mannitol (Parteck M 200, MilliporeSigma), and dicalcium phos- phate (Emcompress, JRS Pharma). The Heckel plot mea- sures the log of 1/porosity as the compression force is Table 1 Compaction properties of commonly used excipients at 50, 100, and 150 megapascals of compression force Material type Compression pressure (MPa) WoC (joules) WoE (joules) YPpl (MPa) YPel (MPa) Ejection (newtons) Porosity TS (MPa) Microcrystalline cellulose (Emcocel 90M) 50.00 1.46 0.12 71.73 876.85 99.50 0.23 4.08 100.00 3.11 0.26 102.36 1090.58 91.33 0.21 5.52 150.00 4.96 0.32 144.28 1256.88 65.53 0.16 6.53 Dicalcium phosphate (Emcompress) 50.00 1.30 0.05 78.32 1492.60 496.60 0.27 0.47 100.00 2.11 0.16 159.56 2300.61 1712.91 0.23 0.77 150.00 3.37 0.21 251.29 2840.36 2327.96 0.17 1.35 Mannitol (Parteck M 200) 50.00 1.70 0.06 103.37 2297.14 2289.39 0.29 0.87 100.00 2.55 0.14 147.33 1922.11 2704.49 0.21 1.37 150.00 3.27 0.21 204.10 2309.08 2909.44 0.16 2.34 Pregelatinized starch (Starch 1500) 50.00 1.44 0.27 102.12 571.20 144.20 0.35 0.17 100.00 2.72 0.42 112.94 657.37 181.20 0.28 0.34 150.00 3.69 0.68 115.70 746.88 205.53 0.21 0.74

